manualshive.com logo in svg

Keysight Y1215B, Installation Notes, Page: 4 / 8

Share
Download
Keysight Y1215B Installation Notes Download Page 4

Figure 2

Attaching the Front Handles and Rear Frame Brackets to Rack Mounting Brackets

(right side brackets shown)

M5 x 0.8 x 10mm 

Torx T-25 

Screws

M4 x 0.7 x 10 mm 
Phillips Flat Head

 

Screws

Y1215B Flush Mount Rack Kit

Y1216A Recess Mount Rack Kit

Front Handle 

M9018-20101

Flush Mount Front Bracket

M9018-00107

Rear Bracket

Rear Frame Bracket

M9018-00108

Recessed Mount Front 

Bracket M9018-00204

M5 x 0.8 x 10mm 

Torx T-25 Screws

Recessed Mount Rear 

Bracket M9018-00205

Rear Frame Bracket

M9018-00108

M4 x 0.7 x 10mm 

Phillips Flat Head 

Screws

Front Handle

M9018-20101

4

Keysight Y1215B and Y1216A Rack Kit Installation Note

Keysight Y1215B Flush Mount Rack Kit, Keysight Y1216A Recessed Mount Rack Kit Installation Note

  Procedure

6

Using the front and rear brackets as templates, position the brackets on the 

rack’s vertical columns where the chassis is to be mounted. Do this for both 

the front and rear brackets on both sides of the rack. Align the bracket holes 

over the “center” holes of the rack units. Slide channel nuts over the rack 

holes to be used by the rack mount flanges. See 

Figure 3

 below and 

Figure 6

 

on page 8.

Summary of Contents for Y1215B









Reviews:

No comments