Keysight U1401B User'S And Service Manual Download Page 125

Page: 125 / 159

Application Examples

Keysight U1401B User’s and Service Guide

125

2-Wire Transmitter Verification

You can use the following method to verify the operation of a 2-wire transmitter.

The method takes advantage of the ability of this instrument to simultaneously

source voltage and measure current.

Turn the rotary switch to

position.

Connect the red alligator lead between the positive output terminal of the

instrument and the positive output terminal of the two-wire transmitter. Refer

Figure 5-16

on page 126.

Connect a shorting plug between the negative output terminal and negative

input terminal of the instrument.

Connect the black alligator lead between the positive input terminal of the

instrument and the negative output terminal of the two-wire transmitter.

The supply can be set to any voltage up to +15 V.

Press

OUTPUT

to output the excitation voltage.

The instrument display will indicate a transmitter output current if an input

signal is present.

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands