Keysight U1401B User'S And Service Manual Download Page 100

Page: 100 / 159

Application Examples

100

Keysight U1401B User’s and Service Guide

Simulation Mode for mA Output

In simulation mode, the instrument simulates a current loop transmitter. Use this

simulation mode when an external DC 24 V or 12 V supply is in series with the

current loop being tested. Always use the special yellow test lead. Follow the

procedure below when performing mA output simulation.

Turn the rotary switch to any one of the

positions.

Connect the special yellow test lead between the positive output terminal of

the instrument and the positive terminal of the measurement device on the

current loop. Refer to

Figure 5-2

on page 101.

Connect the black alligator lead between the

COM

terminal of the loop source

and the negative terminal of the measurement device on the current loop.

Connect the red alligator lead between the negative output terminal of the

instrument and the positive terminal of the current loop source. Make sure the

polarity is correct.

Set the current level of the calibrator between 0 mA and 20 mA. Do not set a

negative current output value.

Press

OUTPUT

to output the test current.

This connection can be used for any loop voltage from 12 V to 30 V.

CAUTION

Always use the supplied special yellow test lead to perform mA simulation.

Disconnect the test lead from the current loop before turning the rotary

switch to change function or to power-off this instrument. Failure to do so

will result in a current of at least 16 mA in the 250

load connected loop.

Summary of Contents for U1401B
































































































































































Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands

Keysight U1401B, User'S And Service Manual

Search results

Summary of Contents for U1401B

Reviews:

Related manuals for U1401B

Brands by name

Popular brands