manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 85 / 276

Share
Download
Keysight N9923A User Manual Download Page 85

Keysight N9923-90001 User’s Guide

                                                                                                                      85

CAT (Cable and Antenna Test) Mode
CAT Mode Settings

Interference Rejection

Use this setting when you suspect that other signals in the area are interfering 
with a measurement. Interference may look like a spike or lack of stability in the 
measurement trace. While monitoring a measurement at a specific frequency, 

toggle this setting between ON and OFF. If the measurement result decreases 
while ON, then there is an interfering signal in the area. Continue to make 
measurements with Interference Rejection ON. However, this will slow the 

measurement speed.

Once enabled, up to SIX sweeps may be required before the interfering signal 

is neutralized.

This setting can be changed at any time without affecting calibration accuracy.

How to set Interference Rejection

— Press 

Meas Setup 4

.

— Then 

Interference Rejection [current setting]

.

— Then choose from the following: 

—

Off

 No interference rejection and fastest possible sweep speed

—

Minimum

 The lowest level of Interference rejection.

—

Medium

 The medium level of Interference rejection.

—

Maximum

 The highest level of Interference rejection.

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments