manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 260 / 276

Share
Download
Keysight N9923A User Manual Download Page 260

 260                                                                                                                     Keysight N9923-90001 User’s Guide

Safety Considerations
Certification and Compliance Statements

EMC

Complies with the essential requirements of the European EMC Directive as 
well as current editions of the following standards (dates and editions are cited 
in the Declaration of Conformity):

— IEC/EN 61326-1

— CISPR Pub 11 Group 1, class B

— AS/NZS CISPR 11

— ICES/NMB-001
This ISM device complies with the Canadian ICES-001.

 

Cet appareil ISM est conforme a la norme NMB-001 du Canada.

Safety

Complies with the European Low Voltage Directive 

— IEC/EN 61010-1 

— Canada: CSA C22.2 No. 61010-1

— U.S.A.: UL std no. 61010-1

South Korean Class B EMC Declaration

This equipment is Class B suitable for home electromagnetic environment and 
is suitable for use in all areas.

Acoustic Statement (European Machinery Directive)

Acoustic Noise Emission

LpA <70 dB

Operator position

Normal operation position per ISO 7779

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments