manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 255 / 276

Share
Download
Keysight N9923A User Manual Download Page 255

Keysight N9923-90001 User’s Guide

                                                                                                                      255

Safety Considerations
Electrostatic Discharge (ESD) Precautions

Electrostatic Discharge (ESD) Precautions

The FieldFox was constructed in an ESD protected environment. This is 

because most of the semiconductor devices used in this instrument are 
susceptible to damage by static discharge.

Static charges are generated in numerous ways, such as simple contact, 
separation of materials, and normal motions of persons working with the 
FieldFox. To prevent instrument damage, practice industry accepted 

techniques for handling static sensitive devices when using the FieldFox. 

Very often, coaxial cables and antennas also build up a static charge, which, if 

allowed to discharge by connecting to the FieldFox, may damage the 
instrument input circuitry. To avoid such damage, it is recommended to 
dissipate any static charges by temporarily attaching a short to the cable or 
antenna prior to attaching to the instrument. 

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments