manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 248 / 276

Share
Download
Keysight N9923A User Manual Download Page 248

 248                                                                                                                     Keysight N9923-90001 User’s Guide

Safety Considerations
For the FieldFox

For the FieldFox

No operator serviceable parts inside except for the lithium-ion 

battery. Refer servicing to qualified personnel. To prevent electrical 

shock do not remove covers. 
If this product is not used as specified, the protection provided by 

the equipment could be impaired. This product must be used in a 

normal condition (in which all means for protection are intact) when 

attached to the AC–DC adapter.
The unit may be used only in the operating conditions and positions 

specified by the manufacturer. 

Do not install substitute parts or perform any unauthorized 

modification to the product. Return the product to Keysight 

Technologies or a designated repair center for service to ensure that 

safety features are maintained.
Applicable local or national safety regulations and rules for the 

prevention of accidents must be observed in all work performed.

Ensure that the connections with information technology equipment 

comply with IEC950 

I

 EN60950.

Observe all ratings and markings of the instrument before 

connecting the instrument.
Maximum Input Voltages and Power:
RF Output Connector: 50V DC, +23 dBm RF
Ext Trig/Ref Connector: 5.5 V DC
RF Input: ±50 VDC, +23 dBm RF
DC Input: 19VDC, 4ADC
When performing a measurement, ensure that the right safety and 

performance ratings of the instrument and accessories are used.
Do not expose the circuit or operate the instrument without its cover 

or while power is being supplied.
Do not operate the instrument in any environment at risk of 

explosion.

The power cord and connectors shall be compatible with the connector 

used in the premise electrical system. Failure to ensure adequate earth 

grounding by not using the correct components may cause product 

damage and serious injury.

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments