manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 243 / 276

Share
Download
Keysight N9923A User Manual Download Page 243

Keysight N9923-90001 User’s Guide

                                                                                                                      243

Working with the Lithium-Ion Battery
Charging the Battery

Using the External Battery Charger (N9910X–872) 

Figure 16-2 

External Battery Charger (N9910X-872)

The external battery charger (N9910X–872), lets you charge a fully depleted 
battery in approximately three hours. It is a two bay, level–3 stand-alone 
battery charger that is compliant with the standard Smart Battery System. The 

two bays are charged sequentially on a first-come, first-served basis, though a 
discharge can be performed in the left bay while the right bay is charging. 

For more information, refer to the Instruction Manual included with the 

external battery charger.

Read the safety information in

 

“For the External Battery Charger 

(N9910X-872)” on page 251

.

External Battery Charger LED

Charging Status

Green

Fully charged

Green flashing

Fast charging

Yellow flashing

Reconditioning – the accuracy of the 

battery’s internal LED charge gauge 

is being renewed. See 

“Reconditioning Battery” on 

page 244

Yellow/green

Battery is reconditioned

Red flashing

Error

Yellow

Standby

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments