Keysight N9923A User Manual Download Page 24

Page: 24 / 276

24 Keysight N9923-90001 User’s Guide

Preparing for Initial Use of Your New FieldFox
FieldFox High Temperature Protection

— To turn Power

OFF

(very low battery drain), press and hold the power

button. Data and instrument state are NOT automatically saved when the

FieldFox is powered OFF. Learn how to save data and instrument state in

Chapter 13, “File Management”, on page 191

. See the Note above

concerning Shut down.

— To restart FieldFox, press the power button and press

Restart

. See the

Note

above concerning Restart.

— Press

Cancel

to exit the power down sequence.

— You can also access the power down softkey menu choices (

Standby

Shut

down

Restart

, and

Cancel

) by using the

Mode

hardkey:

— Press

Mode

—Then

More

—Then

Shut down

— You can make a setting to automatically

Power ON

the FieldFox when a

power source is connected. Learn how on

“Power ON” on page 230

Power Button LED Status

FieldFox High Temperature Protection

The following features prevent degradation or damage in the event of high
internal temperatures in the FieldFox.

How to monitor the internal FieldFox temperature:

— Press

System

, then

Service Diagnostics

— Then

Internal Temperatures

Solid green

Power is ON

Blinking green

FieldFox in Stand By mode

Blinking amber

Battery charging

Blinking amber and green

Stand By mode and battery charging

Not lit

Power is Off and battery is not charging

Do NOT store the FieldFox in the soft-case while powered ON or in

Standby mode.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 24 / 276

Search results

Summary of Contents for N9923A

Reviews: