manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 231 / 276

Share
Download
Keysight N9923A User Manual Download Page 231

Keysight N9923-90001 User’s Guide

                                                                                                                      231

System Settings
LAN Settings

LAN Settings

Configure the LAN settings to be used to communicate with the Data Link 
Software. Learn more about Data Link at: 

www.keysight.com/find/fieldfoxsupport

.

How to configure LAN settings

The first three ‘Current...’ settings can NOT be edited.

— Press 

System 7

.

— Then 

System Configuration

.

— Then 

LAN

.

— Use the 

 arrows to select one of the following, then press 

Edit

.

—

Hostname

 Change the name that can be used to address the FieldFox if 

your server supports this feature. The default hostname is generated 

automatically. 

—

Obtain IP

 Choose from:

Table 14-1 

LAN LEDs (Applies to N9912A units with serial number prefixes 

≥

5607)

LAN LEDs (Applies to N9912A units with serial number prefixes 

≥

5607)

When FieldFox is connected to the LAN, the flashing LAN LEDs have the following 

definitions:

Green: Flashing indicates packets are being transferred.

Yellow:

— Flash, pause = 10 Mbit link speed
— Flash, flash, pause = 100 Mbit link speed
— Flash, flash, flash, pause = 1 GBit link speed

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments