Keysight N9923A User Manual Download Page 222

Page: 222 / 276

222 Keysight N9923-90001 User’s Guide

System Settings
System Configuration

System Configuration

Options (Licensing)

You can view and install options on your FieldFox. To see a comprehensive list

of the options that are available, view the FieldFox Configuration Guide at:

http://literature.cdn.keysight.com/litweb/pdf/5990-9836EN.pdf

How to view the Installed Options

— Press

System 7

— Then

System Configuration

— Then

Options (Licensing)

— Then

Show Options

The currently installed options are listed.

How to Install Options

A.lic file must already be on a USB Flash Drive. To learn how to obtain a.lic file,
visit:

http://www.keysight.com/find/softwarelicense

Insert the USB Flash Drive in the FieldFox.

— Press

System 7

— Then

System Configuration

— Then

Options

— Then

Install Options

The FieldFox reads, validates, then installs the options.

— Press and hold the power button to shut down, then restart the FieldFox.

How to Delete ALL Options

Deleting individual options is NOT supported.

— Press

System 7

— Then

System Configuration

— Then

Options

— Then

Advanced

— Then

Delete All Options

After a warning message, all options on the FieldFox are deleted.

Delete All CFG Options

is to be used by Service Personnel ONLY.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 222 / 276

Search results

Summary of Contents for N9923A

Reviews: