manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 212 / 276

Share
Download
Keysight N9923A User Manual Download Page 212

 212                                                                                                                     Keysight N9923-90001 User’s Guide

System Settings
Display Settings

Trace Width

You can set width of all displayed traces on the FieldFox. This may allow better 
viewing or enhance the look of screen images. This setting can be saved with 

Preferences.

How to set Trace Width

— Press 

System 7

— Then 

Display

— Then 

Display Colors

— Then 

More

— Then 

Trace Wid th

— Then choose one of the following:

—

Normal

 - Standard width.Wide

—

Wide

 - Enhanced width

Title

A custom title can be made to appear in the upper-left corner of the FieldFox 

screen. The title can contain up to approximately 65 alpha-numeric characters. 
To view the Title area, see the Screen Tour in 

“Screen Tour” on page 32

.

How to add or edit a Title

— Press 

System 7

— Then 

Display

— Then 

Title

— Then enter or edit a title using the FieldFox labeler. This is the same labeler 

function that is used to name files. See 

“How to use the FieldFox labeler ” 

on page 193

.

Outdoor Clouds

Outdoor Sun

Night Vision

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments