Keysight N9923A User Manual Download Page 156

Page: 156 / 276

156 Keysight N9923-90001 User’s Guide

Pulse Measurements Mode – Option 330
Pulse Measurement Settings

— Press

Delta Ampl Mkr

— Then choose from the following:

—

AmplMkr 2 value is relative to AmplMkr 1. When AmplMkr 1 is

moved, AmplMkr 2 also moves to maintain the AmplMkr 2 value
between them.

—

OFF

The two amplitude markers move independent of one another.

Marker Search

Use Marker Search to find and move markers to locations on the

Tr 1

trace.

How to Search with Markers

— Activate the marker to be used for the search

— Then press

Mrk ->/Tools

— Then

Marker Search

— Then

Zone Search

— Then choose from the following:

—

Available ONLY when the zoom window is enabled, the search is

limited to the zone defined by the zoom window.

—

OFF

The search is performed over the entire Tr 1 trace.

Then choose from the following:

—

Target

Peak

, and

Minimum

. Learn more about these standard features

beginning in

“Searching with Markers” on page 179

—

Rise Time

Select, then set a value in dB. Delta markers are created and

placed at the Peak and at the specified value BEFORE the Peak.

—

Fall Time

Select, then set a value in dB. Delta markers are created and

placed at the Peak and at the specified value AFTER the Peak.

Rise and Fall time in Marker Search uses different criteria than in Auto

Analysis and will therefore result in different reported values.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 156 / 276

Search results

Summary of Contents for N9923A

Reviews: