Keysight N9923A User Manual Download Page 154

Page: 154 / 276

154 Keysight N9923-90001 User’s Guide

Pulse Measurements Mode – Option 330
Pulse Measurement Settings

— Then

Auto Trigger

— Then choose from the following:

—

Trigger level is determined by the USB Power Sensor firmware.

—

OFF

The trigger level is set manually using the Trigger Level setting.

Trigger Level

Used when Trigger Type = Internal AND Auto Trigger = OFF (Manual).

— Press

Sweep 3

— Then

Trigger

— Then

Trig Level

— Then set the trigger level using the numeric keypad, the

arrows, or the

rotary knob. A line appears on

Tr 1

at the current trigger level setting. Data

acquisition occurs when the RF input signal crosses the line. This setting

can be used with either Positive or Negative edge triggering.

Trigger Settings Annotation

Trigger settings are annotated on the FieldFox screen as highlighted in

red

the following image:

In the previous graphic, the settings are: Trig Level = -10 dBm, Trig Type (Int),

Pos Slope (/), Delay

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 154 / 276

Search results

Summary of Contents for N9923A

Reviews: