Keysight N9923A User Manual Download Page 15

Page: 15 / 276

Keysight N9923A Handheld Analyzer
User’s Guide

Overview

Options and Features

The FieldFox may be ordered to include the following options and features:

Options and Features

Learn More:

RF Vector NA Mode

Chapter 3, “NA

(Network Analyzer)

Mode”, on page 37

2 MHz to 4 GHz (Option 104)

2 MHz to 6 GHz (Option 106)

Forward Measurements S11, S21

Full 2-port S-parameters (Option 122). Adds S22, S12 and

Full 2-port Calibration

Cable and Antenna Test (CAT) Mode (Option

305)

Chapter 5, “CAT

(Cable and Antenna

Test) Mode”, on page

2 MHz to 4 GHz (Option 104)

2 MHz to 6 GHz (Option 106)

Measurements

Distance-to-fault (DTF)

DTF & Return Loss

Return Loss (dB)

VSWR

DTF (VSWR)

Cable Loss (1-Port)

Insertion loss (2-Port)

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 15 / 276

Search results

Summary of Contents for N9923A

Reviews: