Keysight N9923A User Manual Download Page 147

Page: 147 / 276

Keysight N9923-90001 User’s Guide 147

Pulse Measurements Mode – Option 330
Supported Power Sensors

Supported Power Sensors

Pulse measurements are made using any of the Keysight U2020 X-Series USB

Peak Power Sensors.

Zeroing of the U2020 X-Series USB Peak Power Sensors is performed

automatically at power up, every 5 seconds, and prior to measuring low level
signals.

Switching between Pulse Measurement Mode and Power Meter Mode

NOT Supported

- Using a single USB Peak Power Sensor and switching

between Power Meter Mode and Pulse Measurement Mode. Both modes

will attempt to program the sensor, which could cause one or both modes
to hang, or at least report inaccurate data.

Supported

- Using one U2000A Average Power Sensor connected to the

top USB port for Power Meter Mode, and one Peak Power Sensor
connected to the bottom USB port for Pulse Measurement Mode.

How to Connect the Power Sensor

Connect your Power Sensor to one of the FieldFox USB ports.

A sequence of status lights are displayed on the base of the power sensor.

—

Green blinking

light indicates the power sensor is communicating or

self-tests are being performed. Because the FieldFox is usually

communicating with the power sensor when it is connected, this is the
normal mode of operation.

—

Amber light

indicates Zeroing is being performed.

—

Red light

indicates an error has occurred with the power sensor. Refer to

power sensor documentation.

—

No light

indicates the FieldFox is not communicating with the power

sensor. This is the case when in Hold mode or when NOT in Pulsed
Measurement Mode.

Use an attenuator between the DUT and the power sensor when

measuring power levels that are higher than +20 dBm. The attenuator

value can be subtracted from the measurement using the Offset feature,

discussed in

“Relative and Offset Power Measurements” on page 131

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 147 / 276

Search results

Summary of Contents for N9923A

Reviews: