manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 128 / 276

Share
Download
Keysight N9923A User Manual Download Page 128

 128                                                                                                                     Keysight N9923-90001 User’s Guide

Power Meter (USB) Mode
USB Power Meter Settings

USB Power Meter Settings

Select Power Meter Mode before making any setting in this section.

How to select Power Meter Mode

— Press 

Mode_

. 

— Then 

Power Meter (USB Sensor)

.

Average / Peak 

— Press 

Measure 1

— Then choose from the following:

—

Average

 Measures and reports the average of the power 

measurements.

—

Peak

 Available ONLY on the U202x power sensors. Measures and 

reports peak power detected at sensor input.

Zeroing

The Keysight USB Power Sensors perform Internal Zeroing automatically. 
Because Keysight USB Power Sensors have an internal switch, Internal Zeroing 

does NOT require that the power source be turned OFF. 

For highest measurement accuracy, when measuring power levels below –30 

dBm, External Zeroing should be performed. 

During External Zeroing, the power source MUST be turned OFF or the power 

sensor disconnected from the power source (device under test). Power is OFF 
when power sensor measurements are below –60 dBm. When power higher 
than this is detected at the sensor, a warning message is shown on the 

FieldFox and External Zeroing will not proceed.

How to perform External Zeroing

— Press 

Cal 5

.

— Then 

External Zero

.

While either Internal or External Zeroing is being performed, “Zeroing...” is 
shown on the FieldFox screen. While this message is present, do NOT make 

any changes to the FieldFox. 

External Zeroing is NOT allowed on the U2020 X-series Power Sensors.

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments