manualshive.com logo in svg

Keysight N5244AU- H29, Installation Note, Page: 11 / 42

Share
Download
Keysight N5244AU- H29 Installation Note Download Page 11

 10                                                                                                                               Installation Note N5245-90109

Upgrade Kit Order Numbers: N5244AU-921 and N5245AU-921

-

Items Included in the Upgrade Kit

1

Check the contents of your kit against the following list. If any part is missing or 

damaged, contact Keysight Technologies. Refer to 

“Getting Assistance from 

Keysight” on page 4

.

1. In addition to the upgrade kit, the shipment includes an Option Entitlement Certificate. Refer to 

“License 

Key Redemption” on page 6

 for important information about this certificate.

Table 1 

Contents of Upgrade Kit N5245-60109

Ref 

Desig.

Description

Qty

 Part Number

-

Installation note (this document)

1

N5245-90109

-

H29 User’s Guide

1

N5245-90013

Accessory Items
Note to Installer

 

These two items are used when performing vector-corrected noise figure measurements and are not used in the upgrade. 

They are packaged separately in the kit and must remain with the analyzer.
-

2.4 mm male-to-2.4 mm female adapter used to connect an ECal module

1

85056-60007

-

RF cable used to connect an ECal module

1

N5245-20140

Assemblies

A9

Noise receiver board                                                           5201 and above:
                                                                                            5150 and below:

1

N5242-6012

4

Was: 
N5242-60098

A56

Noise bypass switch, port 1

2

N1811-60031 

Was 

N1811-60009

A57

Noise bypass switch, port 2 

A58

Bridge

1

5087-7794 

 

Was 

5087-7729

A59

Noise downconverter

1

5087-7767 

 

Was 

5087-7316

Hardware/Miscellaneous
-

Bracket, port 1 switch

1

N5245-00026

-

Bracket, bridge/port 2 switch 

1

N5245-00032

-

Washer, lock, helical, 3.1 mm-ID, 6.2 mm-OD

2

2190-0584

-

Machine screw, M3.0 x 14, pan head

3

0515-2994 

 

Was 

0515-0665

Summary of Contents for N5244AU- H29











































Reviews:

No comments