Keysight N4372E User Manual Download Page 78

Page: 78 / 152

Keysight N4372E Lightwave Component Analyzer User’s Guide

User Interface Reference

The LCA Function Keys

1 If the LCA server is running, but the function keys are not displayed,

press the [Macro/Local] Utility key until Macro 1 group is shown:

Figure 15 Available macro-buttons on the network analyzer to control the LCA

•

: Brings the LCA user interface to the foreground, to setup an

LCA measurement.

•

: Perform a single sweep measurement with the current

measurement setup.
Pressing this function key when a single or continuous

measurement is running, stops this measurement, and starts

a new single sweep measurement.

•

: Perform continuous measurement sweeps with the current

measurement setup.
Pressing this function key during a single or continuous

measurement, stops the measurement.

•

: Start the optical power monitor. This uses the current

measurement setup to determine the wavelength and the

optical input for which the average optical power is

measured.

Summary of Contents for N4372E

























































































































































Search results

Summary of Contents for N4372E

Reviews:

Keysight N4372E, User Manual, Page: 78 / 152

Search results

Summary of Contents for N4372E

Reviews: