Keysight E8663D User Manual Download Page 78

Page: 78 / 358

64 Keysight E8357D/67D & E8663D PSG User’s Guide

Basic Operation
Configuring the RF Output

This opens a menu of sweep control softkeys and displays a status screen

summarizing all the current sweep settings.

Press

Configure Ramp/Step Sweep

Since ramp is the current sweep type, softkeys in this menu specifically

control ramp sweep settings. When step is the selected sweep type, the

softkeys control step sweep settings. Notice that the

Freq Start

and

Freq

Stop

softkeys appear in this menu in addition to the

Frequency

hardkey

menu.

Press

Sweep Time

to Manual >

sec

In auto mode, the sweep time automatically sets to the fastest allowable

value. In manual mode, you can select any sweep time slower than the

fastest allowable. The fastest allowable sweep time is dependent on the

number of trace points and channels being used on the 8757D and the

frequency span.

Press

Sweep Time

to Auto.

The sweep time returns to its fastest allowable setting.

NOTE

When using an 8757D network analyzer in manual sweep mode, you must

activate the signal generator’s Manual Mode before using the

Manual Freq

softkey to control the sweep. Press

Sweep/List

More (2 of 3) > Manual

Mode On.

Using Alternate

Sweep

Press the

Save

hardkey.

This opens the table editor and softkey menu for saving instrument states.

Notice that the

Select Reg

softkey is active. (For more information on

saving instrument states refer to

“Using the Instrument State Registers”

on page 72

Turn the front panel knob until you find an

available

SAVE

. Remember this saved register number. If no registers are available,

you can write over an

in–use

Re–SAVE

NOTE

When you are using the PSG in a system with an 8757D network analyzer, you

are limited to using registers 1 through 9 in sequence 0 for saving and

recalling states.

Press

Sweep/List

Configure Ramp/Step Sweep

and enter new start and

stop frequency values for the ramp sweep.

Press

Alternate Sweep Register

and turn the front panel knob to select the

Press

Alternate Sweep Off On

to On.

Summary of Contents for E8663D







































































































































































































































































































































































Search results

Summary of Contents for E8663D

Reviews:

Related manuals for E8663D

Brands by name

Popular brands

Keysight E8663D, User Manual

Search results

Summary of Contents for E8663D

Reviews:

Related manuals for E8663D

Brands by name

Popular brands