Keysight E1458A Service Manual Download Page 29 | Manualshive

Page: 29 / 46

Keysight E1458A Service Manual Download Page 29

Keysight E1458A 96-Channel Digital I/O Module Service Guide

31

Performance Verification Tests

Verification Tests

1280 PRINT TAB (10) "Keysight E1458A I/O line failure on port ";J
1290 Errflg=1
1300 END IF
1310 OUTPUT @Dio;"MEAS:DIG:DATA"&VAL$(J)&"?" ! Check the I/O line high
1320 ENTER @Dio;Ready ! Wait for completion
1330 OUTPUT @Dio;"SOUR:DIG:IO"&VAL$(J)&"?"
1340 ENTER @Dio;Bits
1350 IF Bits <> 1 THEN
1360 PRINT TAB (10) "Keysight E1458A I/O line failure on port ";J
1370 Errflg=1
1380 END IF
1390 NEXT J
1400 IF Errflg=1 THEN
1410 PRINT TABXY (1,4) "Keysight E1458A failed FLG, CTL or I/O line test"
1420 ELSE
1430 PRINT TABXY (1,4) "Keysight E1458A FLG, CTL, and I/O line test"
1440 END IF
1450 OUTPUT @Dio;"*RST;*OPC?" ! Clean up
1460 ENTER @Dio;Ready ! Wait for completion
1470 PRINT TABXY (1,5) "Keysight E1458A Test complete"
1480 END

Typical Result

Keysight E1458A passed port programming test

Keysight E1458A passed port data line test

Keysight E1458A passed bit walk test

Keysight E1458A passed FLG, CTL, and I/O test

«
...
27
28
29
30
31
...
»

Summary of Contents for E1458A















































Reviews:

No comments