Keysight DSOX3012T User Manual Download Page 61

Page: 61 / 530

Getting Started

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Access the Built-In Quick Help

To view Quick Help

Press and hold the key or softkey for which you would like to view help.

Sidebar

information and

controls area

The sidebar information area can contain summary, cursors, measurements, or

digital voltmeter information dialogs or it can contain navigation and other

control dialogs.
For more information, see:

•

“Select Sidebar Information or Controls"

on page 49

•

“Undock Sidebar Dialogs by Dragging"

on page 49

Menu line

This line normally contains menu name or other information associated with the

selected menu.

Softkey labels

These labels describe softkey functions. Typically, softkeys let you set up

additional parameters for the selected mode or menu.

Pressing the

Back/Up key at the top of the menu hierarchy turns off softkey

labels and displays additional status information describing channel offset and

other configuration parameters.

Back

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands