Keysight DSOX3012T User Manual Download Page 369

Page: 369 / 530

Web Interface

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

369

Click the

Recall

link.

On the Recall page:

Click

Browse...

In the "Choose file" dialog, select the file you want to recall; then, click

Open

When recalling reference waveform data files, select the

To Reference

Waveform

location.

Click

Recall

Get Image

To save (or print) the oscilloscope's display from the web interface:

Access the oscilloscope's web interface (see

“Accessing the Web Interface"

page 360).

When the oscilloscope's web interface is displayed, select the

Get Image

tab

from the left side of the Welcome screen. After a delay of several seconds, the

oscilloscope's screen image will be displayed.

Right-click on the image and select

Save Picture As...

(or

Print Picture...

Select a storage location for the image file and click

Save

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands