Keysight DSOX3012T User Manual Download Page 362

Page: 362 / 530

362

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Web Interface

The SCPI Command window is useful for testing commands or entering a few

commands interactively. When creating automated programs for controlling the

oscilloscope, you will typically use the Keysight IO Libraries from within a

programming environment like Microsoft Visual Studio (see

“Remote

Programming with Keysight IO Libraries"

on page 366).

Full Scope Remote Front Panel

To operate the oscilloscope using the web interface's Full Scope Remote Front

Panel:

Access the oscilloscope's web interface (see

“Accessing the Web Interface"

page 360).

When the oscilloscope's web interface is displayed, select

Browser Web Control

then select

Full Scope Remote Front Panel

. After a few seconds the Remote Front

Panel appears.

Click keys or knobs that you would normally press on the oscilloscope's front

panel. Drag on edges of knobs to turn them.

NOTE

If Java is not installed on your PC, you will be prompted to install the Java Plug-in. This

plug-in must be installed on the controlling PC for the web interface's Remote Front Panel or

Remote Programming operations.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands