Keysight DSOX3012T User Manual Download Page 30

Page: 30 / 530

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Getting Started

Install the Optional LAN/VGA or GPIB Module

If you need to install a DSOXLAN LAN/VGA module or a DSOXGPIB GPIB module,

perform this installation before you power on the oscilloscope.

If you need to remove a module before installing a different module, pinch the

module's spring tabs, and gently remove the module from the slot.

To install a module, slide the module into the slot on the back until it is fully

seated.

The module's spring tabs will latch into the slot, keeping the module in place.

Tilt the Oscilloscope for Easy Viewing

There are tabs under the oscilloscope's front feet that can be flipped out to tilt the

oscilloscope.

100 Watts MAX

100-240V, 50/60Hz

100-120V, 50/60/400Hz

WARNING: MAIN TAIN
GROUND TO AVOID
ELECTRIC SHOCK

LAN/VGA Module

GPIB Module

Module Slot

NOTE

The LAN/VGA or GPIB module must be installed before powering on the oscilloscope.

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands