Keysight DSOX3012T User Manual Download Page 132

Page: 132 / 530

132

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Digital Channels

Connect the digital probe cable to the DIGITAL Dn - D0 connector on the

mixed-signal oscilloscope. The digital probe cable is keyed so you can connect

it only one way. You do not need to power-off the oscilloscope.

Connect the ground lead on each set of channels (each pod), using a probe

grabber. The ground lead improves signal fidelity to the oscilloscope, ensuring

accurate measurements.

Off

CAUTION

Probe cable for digital channels

Use only the Keysight logic probe and accessory kit supplied with the mixed-signal

oscilloscope (see

“Probes and Accessories"

on page 378).

Channel
Pod Ground

Circuit
Ground

Summary of Contents for DSOX3012T



















































































































































































































































































































































































































































































































































Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands

Keysight DSOX3012T, User Manual

Search results

Summary of Contents for DSOX3012T

Reviews:

Related manuals for DSOX3012T

Brands by name

Popular brands