Keysight 53210A User Manual Download Page 7

Page: 7 / 247

Keysight 53210A User’s Guide

Do Not Operate in an Explosive Atmosphere

Do not operate the instrument in the presence of flammable gases or fumes.

Do Not Operate Near Flammable Liquids

Do not operate the instrument in the presence of flammable liquids or near

containers of such liquids.

Do Not Remove the Instrument Cover

Only qualified, service-trained personnel who are aware of the hazards involved

should remove instrument covers. Always disconnect the power cable and any

external circuits before removing the instrument cover.

Do Not Modify the Instrument

Do not install substitute parts or perform any unauthorized modification to the

product. Return the product to an Keysight Sales and Service Office for service

and repair to ensure that safety features are maintained.

In Case of Damage

Instruments that appear damaged or defective should be made inoperative and

secured against unintended operation until they can be repaired by qualified

service personnel.

Cleaning the Instrument

Clean the outside of the instrument with a soft, lint-free, slightly-dampened cloth.

Do not use detergents or chemical solvents.

Summary of Contents for 53210A
























































































































































































































































Search results

Summary of Contents for 53210A

Reviews:

Brands by name

Popular brands

Keysight 53210A, User Manual

Search results

Summary of Contents for 53210A

Reviews:

Brands by name

Popular brands