manualshive.com logo in svg

Keysight 53210A, User Manual

Share
Download
Keysight 53210A User Manual Download Page 195

Formats and Data Flow

7

Keysight 53210A User’s Guide

195

Front Panel Display

Counter measurements taken from the 

front panel

 or from an IO interface appear 

in the display as indicated in 

Figure 7-1

. See 

Chapter 1

 for an overview of display 

features.

Reading Memory

In addition to being displayed, all counter readings are stored in the counter’s 

volatile

 

reading memory 

(

Figure 7-1

). Memory capacity is 1,000,000 readings. 

Reading memory has the following attributes:

1

reading memory is cleared after a function change, during execution of the 

READ?

, 

INITiate:IMMediate

, or 

MEASure?

 command, after cycling power, or 

following an instrument reset (

*RST

) or preset (

SYSTem:PRESet

).

Table 7-2

Commands Affecting Data Flow

Command

Locations 

Accessed

Readings 

Transferred

Reading Memory 

Cleared

Allowed during 

Measurement

Read?

Front Panel

Reading Memory

Output Buffer

All

No

No

INITiate:IMMediate

Front Panel

Reading Memory

None

Yes

No

FETCh?

Reading Memory

Output Buffer

All

No

No

R?

Reading Memory

Output Buffer

All or 

specified count

Yes

Yes

DATA:REMove?

Reading Memory

Output Buffer

Specified Count

Yes

Yes

DATA:LAST?

Reading Memory

Output Buffer

1

No

Yes

MMEMORY:STORe

:DATA

Reading Memory

Internal Flash 

External USB

All

No

No

Summary of Contents for 53210A
























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands