Keysight Technologies U3047AE04 User'S And Service Manual Download Page 18

Page: 18 / 81

User’s and Service Guide U3047-90002

U3047AE04

System Setup

Hardware Lock-Link Installation (U3021-60002)

Preparing the PNA-X

Figure 5

Rear Bottom Feet

. Install the two rear locking feet (5023-0132) onto the PNA-X, using the included screws

(0515-1619), where the standoffs were removed.

Figure 6

Install Locking Feet on PNA-X

Standoffs (x2)

Feet (x4)

Locking Feet
(5023-0132

, pair

)

Screws (0515-1619)

Included in package

•

5023-0132 - Lock-Links Kit (left, right pair and screws), analyzer

•

0515-2317 - Screw T15 M3.5 x 0.6 12 mm

•

N5242-20138 - Right Lock-Link, test set

•

N5242-20139 - Left Lock-Link, test set

1. The Lock-Link Kit (U3021-60002) includes:

2. Remove the feet from the bottom of the PNA-X.
3. Remove the two lower standoffs and screws (0515-1619) from the rear panel on the PNA-X

using a T20 Torx driver.

(

T20 M4 x 0.7 2

Summary of Contents for U3047AE04


















































































Search results

Summary of Contents for U3047AE04

Reviews:

Related manuals for U3047AE04

Brands by name

Popular brands

Keysight Technologies U3047AE04, User'S And Service Manual

Search results

Summary of Contents for U3047AE04

Reviews:

Related manuals for U3047AE04

Brands by name

Popular brands