Keysight Technologies S9106AC-2IF Startup Manual Download Page 5 | Manualshive

Page: 5 / 80

background image

1 Overview

S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions, Startup Guide

1

1 Overview

Keysight S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions are
streamlined, non-signaling measurement systems that enable automated testing of
5G New Radio (5G NR) infrastructure equipment.

S9106AC-2IF 5G FR1
Multi-port Transceiver contains:
two Transceiver Channels,
380 MHz to 6 GHz,
with MIMO Subsystem
and 7 to 15 GHz High IF
on Two Channels

S9106AC-4UP 5G FR1
Multi-port Transceiver contains:
four Transceiver Channels,
380 MHz to 6 GHz,
with MIMO Subsystem

S9106AC-42D 5G FR1
Multi-port Transceiver
contains: four Transceiver
Channels, 380 MHz to 6 GHz,
with MIMO Subsystem
and 7 to 15 GHz High IF
on Two Channels

In this document...

This document describes the installation process to start up and prepare the
Keysight S9106AC-2IF, -4UP, and -42D 5G FR1 Multi-port Transceiver Solutions.

1. Review this Overview

2.

Review Safety Requirements

3.

Review Hardware

4.

Install Hardware

5.

Install Software

6.

Verify Operation

7.

«
...
3
4
5
6
7
...
»

Summary of Contents for S9106AC-2IF

















































































Reviews:

No comments

Related manuals for S9106AC-2IF

Brand: 4iiii Pages: 3

Brand: Dallas Brass Pages: 19

Brand: National Instruments Pages: 38

Brand: Vaisala Pages: 2

Brand: Vega Pages: 28

Brand: Vega Pages: 20

Brand: Ecolab Pages: 95

Brand: Lutron Electronics Pages: 13

Brand: FISCHER Pages: 20

Brand: DriveTest Pages: 24

Brand: Mannix Pages: 5

Brand: Power Measurement Pages: 20

Brand: Sage Pages: 75

Brand: Harken Pages: 2

Brand: Huvitz Pages: 58

Brand: M-Audio Pages: 21

Brand: GasQuip Pages: 8

EnviroAlert EA200

Brand: Winland Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands