manualshive.com logo in svg

Keysight Technologies S9100A, Startup Manual

Share
Download
Keysight Technologies S9100A Startup Manual Download Page 36

3 Review Hardware Components

3. 2. 6. 6 Connectors, E7770A CIU Rear Panel, Controller Card

Each E7770A CIU contains a single CONTROLLER CARD. The status of the
E7770A CIU is identified using the status lights on the CONTROLLER CARD.

Status LEDs

Top Left LED, Green

On, ind12 V supply if okay.

Top Right LED, Green

On, indicates configured okay.

Bottom Left LED, Red

Not used.

Bottom Right LED, Green

On, indicates configured okay.

USB

Connector

Micro-USB B
Reserved for Keysight internal use only.

CONTROL (LAN)

Connector

10/100/1000BASE-T
(RJ-45) Gigabit Ethernet Port

TRIG 1

Connector

BNC (f), 50 Ω,

nominal

Input Level Range

5 V TTL (Trigger signal below 0.8 volts is a
"zero" (low) and anything above +2.4 volts is a
"one" (high).

TRIG 2

Connector

BNC (f), 50 Ω,

nominal

Input Level Range

5 V TTL (See description for TRIG 1.)

TRIG 3

Connector

BNC (f), 50 Ω,

nominal

Input Level Range

5 V TTL (See description for TRIG 1.)

TRIG 4

Connector

BNC (f), 50 Ω,

nominal

Input Level Range

5 V TTL (See description for TRIG 1.)

Ctrl 1

Connector

Micro-HDMI
Reserved for Keysight internal use only.

Ctrl 2

Connector

Micro-HDMI
Reserved for Keysight internal use only.

32

S9100A 5G Multi-Band Vector Transceiver, Startup Guide

Summary of Contents for S9100A












































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands