manualshive.com logo in svg

Keysight Technologies NFA X-Series, Getting Started And Troubleshooting Manual

Share
Download
Keysight Technologies NFA X-Series Getting Started And Troubleshooting Manual Download Page 60

 60                                                                Keysight NFA X-Series Getting Started and Troubleshooting Guide

Instrument Operating System
USB Connections

USB Connections

All of the USB ports are compatible with the USB 2.0/3.0 and 1.1 specification. 

The three USB ports on the front panel (see graphic below) and three of the 

USB ports on the rear panel are USB Series “A” ports. These are ports to which 

you can connect USB mass storage devices and printers. The instrument USB 

Host support includes the standard Microsoft Windows USB drivers for human 

interface, mass storage, printing, scanning, and imaging devices. A complete 

up-to-date list of the Windows USB class driver support is available on the 

Microsoft website. 

The square USB port (see graphic below) on the rear panel is a USB 3.0 Series 

“B” port and is used for controlling the instrument over USB. Information to 

help you program your instrument is documented in the X-Series 

Programmer’s Guide. The instrument USB device driver included in the 

instrument software supports the test and measurement industry standard 

USBTMC-USB488 device class.

In addition, the IO Libraries CD that was included with your instrument 

contains USB Host drivers that allow control of other instruments connected to 

the USB ports.
Keysight Technologies does not support or warrant correct instrument 

operation if additional USB drivers from third parties are installed in the 

instrument. It is possible that additional drivers could break the normal USB 

operation. If USB operation is broken, recovery would require reinstalling the 

instrument application using the Instrument recovery process.

 

Summary of Contents for NFA X-Series




































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands