manualshive.com logo in svg

Keysight Technologies N9010A Series, Installation Note

Share
Download
Keysight Technologies N9010A Series Installation Note Download Page 61

Installation Note N9010-90054

61

Installation Procedure

Verify Hardware Installation

1.

Verify the spectrum analyzer application loads and sweeps as expected. 

2.

Press 

System

, 

Show

, 

Hardware

 on the analyzer and verify that the DIF, EAIF, and EFEC boards 

identify themselves as:

—

Analog IF (Hw Id = 57)

—

Digital IF (Hw Id = 72)

—

Front End Controller (Hw Id = 41 or 75)

Verify Optional Functionality

1.

Press 

Mode

, 

IQ Analyzer (Basic)

.

2.

Press 

Mode Setup

.

3.

Press 

IF Path

.

4.

Verify that softkeys appear labeled “

25 MHz

” and “

40 MHz

”.

5.

Press 

AMPTD Y Scale

, 

More 1 of 2

, 

uW Path Control

.

6.

Verify that softkeys appear labeled “

Standard Path

” and “

uW Preselector Bypass

”.

7.

Press 

uW Preselector Bypass

. If the path was previously set to 

Standard Path

, you should hear 

a click.

8.

Press 

Standard Path

. If the path was previously set to 

uW Preselector Bypass

 path, you should 

hear a click.

Perform Preselector Characterization

1.

Press 

System

, 

Alignments

, 

More

, 

Advanced

.

2.

Press 

Characterize Preselector

, 

Enter

. The characterization will take several minutes.

3.

Wait until the analyzer resumes sweeping.

Summary of Contents for N9010A Series
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands