Keysight Technologies N5221BU-605 Installation Note Download Page 76

Page: 76 / 88

76 Installation Note N5222-90114

Installation Procedure for the Upgrade

Step 52. Verify the PNA Analyzer Program is Running with the Correct

Options

Start the Network Analyzer program.

Once the Network Analyzer program is running:

—

Press

Help

About NA

and verify that Option 405 is listed in the

PNA application.

After successful installation of all upgrades, some features require some

adjustments to ensure the instrument meets its specified performance.

Refer to the following Web site:

http://na.support.keysight.com/pna

If the option is still not enabled or if your old option(s) have been removed,

contact Keysight Technologies. Refer to

“Getting Assistance from

Keysight” on page 4

Summary of Contents for N5221BU-605

























































































Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands

Keysight Technologies N5221BU-605, Installation Note

Search results

Summary of Contents for N5221BU-605

Reviews:

Related manuals for N5221BU-605

Brands by name

Popular brands