Keysight Technologies N5221B Manual Download Page 26 | Manualshive

Page: 26 / 88

background image

26 Installation Note N5222-90131

Description of the Upgrade
Installation Procedure for the Upgrade

-

— W42 (N5222-20073) A21 HMA26.5 to A23 mixer brick
— W12 (N5222-20068) Port 1 CPLR THRU to A29 port 1 coupler
— W12 (N5222-20068) Port 1 CPLR THRU to A29 port 1 coupler
— W123 (N5222-20123) A29 port 1 coupler to front-panel Port 1 A71 bias T

combiner

— W24 (N5222-20069) Port 2 CPLR THRU to A32 port 2 coupler
— W117 (N5222-20071) A32 port 2 coupler to front-panel Port 2 CPLR ARM

These cables must be saved - they will be reinstalled.

— W4 (N5222-20040) W3 to A25 port 1 receiver coupler
— W10 (N5222-20043) W9 to A24 port 2 receiver coupler
— W13 (N5222-20005) A25 port 1 receiver coupler to A33 reference mixer

switch

— W36 (N5222-20032) REF 1 RCVR R1 IN to A33 reference mixer switch
— W35 (N5222-20033) A33 reference mixer switch to front-panel REF 1

SOURCE OUT

— W30 (N5222-20091) (qty = 6) Front panel jumper

Step 13. Remove the A23 Mixer Brick Assembly

Remove the A23 mixer brick assembly from the PNA. For instructions, click the

Chapter 7 bookmark, “Removing and Replacing the A23 and A24 Mixer Bricks”
in the PDF Service Guide

1

.

Remove and save the cable guards for the front panel jumpers.

1. See

“Downloading the Online PNA Service Guide” on page 8

«
...
24
25
26
27
28
...
»

Summary of Contents for N5221B

























































































Reviews:

No comments

Related manuals for N5221B

Brand: Lambrecht Pages: 5

Brand: Keithley Pages: 25

Brand: DAKOTA ULTRASONICS Pages: 48

Brand: TE Connectivity Pages: 9

Brand: OHAUS Pages: 84

Brand: NARDA Pages: 64

Brand: National Instruments Pages: 38

Clavinova CVP-601

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 28

Brand: Olimpus Pages: 12

Brand: Ecolab Pages: 95

Brand: E-Mon Pages: 72

ENERGETIQ LDLS EQ-99X

Brand: Hamamatsu Pages: 45

Brand: Genie Pages: 14

Brand: Magnescale Pages: 2

Brand: Datakom Pages: 27

microCLIMA ULTRA

Brand: MADDALENA Pages: 17

PHYSICS line C.A 832

Brand: Chauvin Arnoux Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands