manualshive.com logo in svg

Keysight Technologies N5221A, Service Manual, Page: 291 / 368

Share
Download
Keysight Technologies N5221A Service Manual Download Page 291

Keysight N5221A/22A Service Guide                                                                                            7-27

Repair and Replacement Procedures
Removing and Replacing the A18 GPIB Board

Removing and Replacing the A18 GPIB Board

Tools Required

— T-10 TORX driver (torque to 9 in-lb or 1.02 N.m) 
— T-20 TORX driver (torque to 21 in-lb or 2.38 N.m)
— ESD grounding wrist strap

Removal Procedure

Refer to 

Figure 7-11

 for this procedure.

1.

Disconnect the power cord.

2.

Remove the outer and inner covers. Refer to 

“Removing the Covers” on 

page 7-6

.

3.

Remove the A16 power supply assembly. Refer to 

“Removing and 

Replacing the A16 Power Supply Assembly” on page 7-23

.

4.

Remove the A17 CPU board assembly. Refer to 

“Removing and Replacing 

the A17 CPU Board Assembly” on page 7-25

.

5.

Remove the rear panel. Refer to 

“Removing and Replacing the Rear Panel” 

on page 7-52

.

6.

Slide the A18 GPIB board out the rear of the analyzer.

Replacement Procedure

1.

Reverse the order of the removal procedure.

2.

Perform the post-repair adjustments, verifications, and performance tests 

that pertain to this removal procedure. Refer to 

Table 7-2 on page 7-60

. 

Summary of Contents for N5221A

















































































































































































































































































































































































Reviews:

No comments