Keysight Technologies N5221A Service Manual Download Page 277

Page: 277 / 368

Keysight N5221A/22A Service Guide 7-13

Repair and Replacement Procedures
Removing and Replacing the A1–A3 and Other Front Panel Subassemblies

Figure 7-4

A3 Display Assembly and Touch Screen Removal

The display cable (item

⑥

) can be removed by removing the three screws

(item

⑦

) that attach it to the LCD display hold down bracket (item

⑧

The LCD display can be removed by disconnecting the LCD cable from the
inverter board and then removing the four screws (item

⑨

) that attach it to

the LCD display hold down bracket (item

⑧

). Note the location of the four

spacers (item

⑩

) before separating the LCD display from the hold down

bracket.

Summary of Contents for N5221A

















































































































































































































































































































































































Search results

Summary of Contents for N5221A

Reviews:

Keysight Technologies N5221A, Service Manual, Page: 277 / 368

Search results

Summary of Contents for N5221A

Reviews: