manualshive.com logo in svg

Keysight Technologies M1749A, Getting Started Manual, Page: 38 / 41

Share
Download
Keysight Technologies M1749A Getting Started Manual Download Page 38

 38                                                                                                                                          Getting Started Guide

Troubleshooting
Where to get technical help

Where to get technical help

For online assistance: 

http://www.keysight.com/find/assist

To contact Keysight Technologies: 

http://www.keysight.com/find/contactus

Also, see 

“Locations for Keysight Technologies” on page 40

.

Identifying Problems

If the status indicator on the M1749A is not lit, or if it appears that mmWave 

signals are not being exchanged with the Device Under Test check the 

following: 

1.

Are the RF cables connected appropriately between the M1749A and the 

measurement instrument? (See 

Figure 2-1 on page 18

.)

2.

Is the M1749A powered on?

3.

Is the PXIe chassis (and its measurement instruments) powered on?

4.

Is the measurement application properly configured (for example, are the 

input and output ports selected appropriately for your test setup?).

If no obvious problem in the test setup can be found, contact Keysight 

Technologies to ask for technical support. 

No operator serviceable parts inside. Refer servicing to qualified personnel. To 

prevent electrical shock do not remove covers. 

Summary of Contents for M1749A










































Reviews:

No comments