Keysight Technologies InfiniiVision 3000 X Series User Manual Download Page 64

Page: 64 / 432

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

Vertical Controls

The ground level of the signal for each displayed analog channel is identified by
the position of the

icon at the far-left side of the display.

To turn waveforms on or off (channel or math)

Press an analog channel key turn the channel on or off (and to display the

channel's menu).

When a channel is on, its key is illuminated.

Channel,
Volts/div

Channel 1
ground
level

Trigger
source

Trigger level
or threshold

Channel 2
ground
level

NOTE

Turning channels off

You must be viewing the menu for a channel before you can turn it off. For example, if channel

1 and channel 2 are turned on and the menu for channel 2 is being displayed, to turn channel

1 off, press

[1]

to display the channel 1 menu; then, press

[1]

again to turn channel 1 off.

Summary of Contents for InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands

Keysight Technologies InfiniiVision 3000 X Series, User Manual

Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands