Keysight Technologies InfiniiVision 3000 X Series User Manual Download Page 422

Page: 422 / 432

422

Keysight InfiniiVision 3000 X-Series Oscilloscopes User's Guide

UART/RS232 Triggering and Serial Decode

Interpreting UART/RS232 Lister Data

In addition to the standard Time column, the UART/RS232 Lister contains these

columns:
• Rx — receive data.
• Tx — transmit data.
• Errors — highlighted in red, Parity Error or Unknown Error.

Aliased data is highlighted in pink. When this happens, decrease the horizontal

time/div setting and run again.

Searching for UART/RS232 Data in the Lister

The oscilloscope's search capability lets you search for (and mark) certain types of

UART/RS232 data in the Lister. You can use the

[Navigate]

key and controls to

navigate through the marked rows.

With UART/RS232 selected as the serial decode mode, press

[Search]

In the Search Menu, press the

Search

softkey; then, turn the Entry knob to select

the serial slot (Serial 1 or Serial 2) on which the UART/RS232 signals are being

decoded.

In the Search Menu, press

Search

; then, select from these options:

Summary of Contents for InfiniiVision 3000 X Series

















































































































































































































































































































































































































































Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands

Keysight Technologies InfiniiVision 3000 X Series, User Manual

Search results

Summary of Contents for InfiniiVision 3000 X Series

Reviews:

Related manuals for InfiniiVision 3000 X Series

Brands by name

Popular brands