Keysight Technologies E4981A Service Manual Download Page 46

Page: 46 / 152

Chapter 4

Troubleshooting

To Troubleshoot the Instrument

Figure 4-1

Primary trouble isolation flowchart

㪼㪋㪐㪏㪈㪸㫊㪼㪈㪇㪇㪌

Power on

Power up normally?

Go to Power on Sequence

Troubleshooting

Go to Troubleshooting

Using Service Function

Go to Power on Sequence

Troubleshooting

Power on test pass?

Error message is

displayed?

Go to Function Specific

Troubleshooting*

(To Check the LCD)

Yes

Power on

Power on test

Go to Troubleshooting

Using Service Function

Power on test pass?

Yes

End

Performance test

Go to Performance Test

Failure Troubleshooting

Performance test pass?

Yes

* In case of display scan,
brightness and color problems.

Display and Boot-up Problems

Problems on Measurement Performance and Measurement Result

Problems on Front Panel, LCD Display,
Front USB Port, GPIB Interface, USB
Interface, LAN Port, External Trigger Input,
Handler Interface or Scanner Interface.

Power on

Go to Function Specific

Troubleshooting

Summary of Contents for E4981A

























































































































































Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands

Keysight Technologies E4981A, Service Manual

Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands