Keysight Technologies E4981A Service Manual Download Page 16

Page: 16 / 152

Chapter 1

General Information

Organization of Service Guide

Tabs are used to divide the major chapter and appendix of this manual. The contents of
each chapter and appendix in this manual as follows.

•

Chapter 1, “General Information.”

This Service Guide is a guide to servicing the E4981A 20 Hz/1 kHz/1 MHz
Capacitance Meter. The Service Guide provides information about performance test,
adjustment, troubleshooting, and repairing the E4981A.

•

Chapter 2, “Performance Test.”

This chapter provides the outline of the E4981A performance tests.

•

Chapter 3, “Adjustment.”

This chapter provides the adjustment information for the E4981A to ensure that it is
within its specifications. The adjustment must be performed Keysight’s qualified
service personnel. If you need the adjustment for your E4981A, it should be sent to the
nearest Keysight Technologies service office.

•

Chapter 4, “Troubleshooting.”

This chapter provides the procedure to isolate a faulty assembly in the E4981A.

•

Chapter 5, “Replaceable Parts.”

This chapter contains information for ordering replacement parts for the E4981A.

•

Chapter 6, “Replacement Procedure.”

This chapter provides procedure for removing and replacing the major assemblies in
the E4981A.

•

Chapter 7, “Post-Repair Procedures.”

This chapter lists the procedures required to verify the E4981A operation after an
assembly is replaced with a new one.

•

Appendix A, “Manual Changes.”

This appendix contains the information required to adapt this manual to versions or
configurations of the E4981A manufactured earlier than the current printing date of this
manual. The information in this manual applies directly to E4981A units with the serial
number that is printed on the title page of this manual.

•

Appendix B, “Firmware Update.”

This appendix describes how to update the E4981A firmware. When you want to
update the E4981A firmware, refer to this appendix.

•

Appendix C, “Power Requirement.”

•

Appendix D, “Error Messages.”

The Keysight E4981A provides error messages to indicate its operating status. This
appendix describes the error messages of the E4981A in alphabetical order.

Summary of Contents for E4981A

























































































































































Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands

Keysight Technologies E4981A, Service Manual

Search results

Summary of Contents for E4981A

Reviews:

Related manuals for E4981A

Brands by name

Popular brands