Keysight Technologies E4981A Service Manual Download Page 148 | Manualshive

Page: 148 / 152

background image

146

Appendix D

Error Messages

Error Messages

O

47

OPEN measurement incomplete

This error occurs when the cable correction OPEN measurement is incomplete.

-321

Out of memory

The E4981A has insufficient memory to perform the requested operation.

P

1080

Power failed

Power unit hardware failure is detected.

Contact Keysight Technology’s Sales and Service Office or the company from which you
purchased the device.

-108

Parameter not allowed

The number of parameters is larger than required by the command. For example, although
the

:CREJ:LIM

command requires one parameter such as “

:CREJ:LIM 3

”, two

parameters are added to give “

:CREJ:LIM 0,3

”.

-112

Program mnemonic too long

The length of the header exceeds 12 characters. (Refer to IEEE488.2,7.6.1.4.1.)

Q

-350

Queue overflow

The queue contains a certain code other than the code that caused this error. This indicates
that an error has occurred due to insufficient space in the queue but has not been recorded.

-400

Query error

A comprehensive Query error has occurred for which the E4981A cannot detect further
details. This code simply indicates the occurrence of a Query error that is defined in
IEEE488.2,11.5.1.1.7 and 6.3.

-410

Query INTERRPUTED

This indicates the status that causes an “INTERRUPTED” Query error. (Refer to
IEEE488.1,6.3.2.3.) This error occurs, for example, when data byte (DAB) or GET is
received after Query but before the response has been completely sent.

-420

Query UNTERMINATED

This indicates the status that causes an “UNTERMINATED” Query error. (Refer to
IEEE488.2,6.3.2.) This error occurs, for example, when the E4981A is specified as a talker
and an incomplete program message is received.

-430

Query DEADLOCKED

This indicates the status that causes a “DEADLOCKED” Query error. (Refer to
IEEE488.2,6.3.1.7.) This error occurs, for example, when both input and output buffers
become full and the E4981A cannot continue processing.

«
...
146
147
148
149
150
...
»

Summary of Contents for E4981A

























































































































































Reviews:

No comments

Related manuals for E4981A

Brand: Kane Pages: 16

Brand: Bacharach Pages: 48

Brand: Bacharach Pages: 24

Brand: Macnaught Pages: 14

Brand: Magtrol Pages: 83

Brand: janitza Pages: 6

Brand: janitza Pages: 36

Brand: Olympus Pages: 12

Brand: RADWAG Pages: 12

Brand: Samsara Pages: 16

Brand: RHS Pages: 8

Brand: Tohnichi Pages: 12

Concert Performer Series Digital Piano CP110

Brand: Kawai Pages: 149

Brand: CAS Corporation Pages: 20

Brand: Sensitech Pages: 2

Brand: Tektronix Pages: 116

AcuRev 1310 Series

Brand: AccuEnergy Pages: 109

EUROGRAND EG2080

Brand: Behringer Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands