Keysight Technologies E4981A Service Manual Download Page 144 | Manualshive

Page: 144 / 152

background image

142

Appendix D

Error Messages

Error Messages

Error Messages

An error message is displayed in the instrument status display area in the lower-left part of
the screen. Pressing the cursor arrow key on the front panel or executing the :DISP:CCL
command clears the error message. Moreover, about a specific error message, when a
sweep is started again, the display of an error message may disappear. Errors caused by
operation of a front panel key simply appear on the display; with a few exceptions, these
are not stored in the error queue.

The log of an error message, a maximum of 100 pieces are recorded, and it can go back and
check from the oldest error. Executing the :SYST:ERR? command checks error logs. This
operation can be performed only by "SCPI" command. It cannot be operated from the front
panel.

An error with a positive error number is one uniquely defined for this instrument. On the
other hand, an error with a negative error number is basically one defined for common
GPIB devices in IEEE488.2.

1 - 100

21

1 MHz opt. not installed

This error occurs when cable correction commands are sent to E4981A with Option 002,
via GPIB/LAN/USB. This error is not generated with front panel operation.

A

1103

A1 EEPROM write error

An error is generated while writing data to A1 EEPROM.

Contact Keysight Technology’s Sales and Service Office or the company from which you
purchased the device.

B

-168

Block data not allowed

A block data element has been received where the E4981A does not accept any block data
element.

C

41

Correction Measurement Aborted

This error occurs when the correction data measurement is aborted.

1200

CPU bd FLASH ROM write error

An error is generated while writing data to FLASH.

Contact Keysight Technology’s Sales and Service Office or the company from which you
purchased the device.

«
...
142
143
144
145
146
...
»

Summary of Contents for E4981A

























































































































































Reviews:

No comments

Related manuals for E4981A

Brand: Kane Pages: 19

Brand: PASCO Pages: 3

Brand: PASCO Pages: 2

Brand: NanoPhotometer Pages: 133

Brand: Veeder-Root Pages: 59

Brand: KBR Pages: 12

Brand: Palstar Pages: 15

Brand: Sonel Pages: 84

Ratio:Guard Advanced

Brand: H.E. Anderson Pages: 9

Brand: Omega Pages: 20

Brand: Ntron Pages: 29

Brand: Bruker BioSpin Pages: 76

Brand: pts Diagnostics Pages: 2

LeakTracker OIL-GLO ULTRA

Brand: Spectroline Pages: 12

Brand: Omega Pages: 4

Brand: Z-TRAUQ Pages: 10

Brand: Kirby Morgan Pages: 101

Brand: BASI Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands