manualshive.com logo in svg

Keysight Technologies DSO-X 2014A, User Manual

The Keysight Technologies DSO-X 2014A is a high-performance oscilloscope designed for accurate measurements and analysis. To make the most of its features, be sure to download the free User Manual from manualshive.com. This manual provides detailed instructions on how to operate and maximize the capabilities of this powerful tool.

Share
Download
background image

CAN/LIN Triggering and Serial Decode

23

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

341

 

• If the total frame count exceeds the length specified in the standard, TFM will 

appear red (LIN 1.3 only).

• For LIN 1.3 a wakeup signal is indicated by WAKE in blue. If the wakeup signal 

is not followed by a valid wakeup delimiter a wakeup error is detected and 

displayed as WUP in red.

Interpreting LIN Lister Data

In addition to the standard Time column, the LIN Lister contains these columns:
• ID — frame ID.
• Data — (LIN 1.3 only) data bytes.
• Checksum — (LIN 1.3 only).
• Data and Checksum — (LIN 2.0 only).
• Errors — highlighted in red.

Aliased data is highlighted in pink. When this happens, decrease the horizontal 

time/div setting and run again.

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Reviews:

No comments

Related manuals for DSO-X 2014A

Handler IV Operator'S Manual preview
IV
Brand: Handler Pages: 25
Wahl 2001 Operating Instructions Manual preview
2001
Brand: Wahl Pages: 47
UNI-T UT673A Quick Start Manual preview
UT673A
Brand: UNI-T Pages: 4
UNI-T UPO3000E Series Programming Manual preview
UPO3000E Series
Brand: UNI-T Pages: 94
Underhill Tracker T-400 Assembly Instructions And Operation Manual preview
Tracker T-400
Brand: Underhill Pages: 12
UMS HYPROP User Manual preview
HYPROP
Brand: UMS Pages: 92
GE Innova 2000 Preinstallation Manual preview
Innova 2000
Brand: GE Pages: 176
Triton Blue TB-1500S User Manual preview
TB-1500S
Brand: Triton Blue Pages: 11
ZIEHL-ABEGG ZA top SM315.100A Original Operating Instructions preview
ZA top SM315.100A
Brand: ZIEHL-ABEGG Pages: 76
SAC SAC-LEAD-LED Installation preview
SAC-LEAD-LED
Brand: SAC Pages: 2
Phenix Technologies BK130 User Manual preview
BK130
Brand: Phenix Technologies Pages: 39
Triton ARGO G60 Installation Manual preview
ARGO G60
Brand: Triton Pages: 31
GAPOSA M3A Reference Manual preview
M3A
Brand: GAPOSA Pages: 32
OMGA TR 2B INC INT NC Operation And Maintenance Manual preview
TR 2B INC INT NC
Brand: OMGA Pages: 76
ABB TPL85-B12 Operation Manual preview
TPL85-B12
Brand: ABB Pages: 154
Major tech MT474 Instruction Manual preview
MT474
Brand: Major tech Pages: 12
Atos Medical CareTips Provox FreeHands FlexiVoice Quick Start Manual preview
CareTips Provox FreeHands FlexiVoice
Brand: Atos Medical Pages: 2
Kurzweil MS-1 MICRO SEQUENCER - MUSICIAN S GUIDE Manual preview
MS-1 MICRO SEQUENCER - MUSICIAN S GUIDE
Brand: Kurzweil Pages: 91

Brands by name

Popular brands

Load more brands