manualshive.com logo in svg

Keysight Technologies DSO-X 2014A, User Manual

The Keysight Technologies DSO-X 2014A is a high-performance oscilloscope designed for accurate measurements and analysis. To make the most of its features, be sure to download the free User Manual from manualshive.com. This manual provides detailed instructions on how to operate and maximize the capabilities of this powerful tool.

Share
Download
background image

Utility Settings

20

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

279

 

File Explorer

The File Explorer lets you navigate the oscilloscope's internal file system and the 

file systems of connected USB storage devices.

From the internal file system, you can load oscilloscope setup files or mask files.

From a connected USB storage device, you can load setup files, mask files, license 

files, firmware update (*.ksx) files, label files, etc. Also, you can delete files on a 

connected USB storage device.

The oscilloscope's internal file system, under "\User Files", consists of 10 locations 

for oscilloscope setup files, and four locations for mask files.

To use the File Explorer:

1

Press 

[Utility] > File Explorer

.

2

In the File Explorer Menu, press the softkey in the first position and use the 

Entry knob to navigate.

NOTE

The USB port on the front panel, and the USB port on the rear panel labeled "HOST" are USB 

Series A receptacles. These are the receptacles to which you can connect USB mass storage 

devices and printers.
The square receptacle on the rear panel labeled "DEVICE" is provided for controlling the 

oscilloscope over USB. See the 

Programmer's Guide

 for more information.

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Reviews:

No comments

Related manuals for DSO-X 2014A

Tacx Cosmos Assembling Instructions preview
Cosmos
Brand: Tacx Pages: 2
C.E. Nierhoff & Co C520 Troubleshooting Manual preview
C520
Brand: C.E. Nierhoff & Co Pages: 7
Bartscher 1500/17 Original Instruction Manual preview
1500/17
Brand: Bartscher Pages: 28
Bartscher IV-65 Instruction Manual preview
IV-65
Brand: Bartscher Pages: 13
IBEX TS100 Quick Start Manual preview
TS100
Brand: IBEX Pages: 10
M-system R3 Series Instruction Manual preview
R3 Series
Brand: M-system Pages: 12
MADRIX NEO Quick Start Manual & Technical Manual preview
NEO
Brand: MADRIX Pages: 12
Narcotrend Compact M Operating Instructions Manual preview
Compact M
Brand: Narcotrend Pages: 47
EarthQuaker Devices The Wave Transformer Manual preview
The Wave Transformer
Brand: EarthQuaker Devices Pages: 21
Konica Minolta DF-619 Service Manual preview
DF-619
Brand: Konica Minolta Pages: 32
Accurate Technology VALIANT Owner'S Manual preview
VALIANT
Brand: Accurate Technology Pages: 10
Gage Bilt GB924 Original Instructions Manual preview
GB924
Brand: Gage Bilt Pages: 28
MMF POS 2261998USBA1-XX Instruction Manual & User Manual preview
2261998USBA1-XX
Brand: MMF POS Pages: 5
U-Line H-8379 Manual preview
H-8379
Brand: U-Line Pages: 6
TECshow MAGIC CUBE User Manual preview
MAGIC CUBE
Brand: TECshow Pages: 22
Beamz MHL 108 WASH 150.509 Instruction Manual preview
MHL 108 WASH 150.509
Brand: Beamz Pages: 32
SYNBIOSIS Protos 3 Quick Manual preview
Protos 3
Brand: SYNBIOSIS Pages: 2
Harman DriveRack VENU360 Quick Start Manual preview
DriveRack VENU360
Brand: Harman Pages: 4

Brands by name

Popular brands

Load more brands