manualshive.com logo in svg

Keysight Technologies DSO-X 2014A, User Manual

The Keysight Technologies DSO-X 2014A is a high-performance oscilloscope designed for accurate measurements and analysis. To make the most of its features, be sure to download the free User Manual from manualshive.com. This manual provides detailed instructions on how to operate and maximize the capabilities of this powerful tool.

Share
Download
background image

Display Settings

8

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

129

 

1

Press 

[Display]

.

2

Press the 

Grid

 softkey; then, turn the Entry knob 

 to select the grid type.

To adjust the grid intensity

To adjust the display grid (graticule) intensity:

1

Press 

[Display]

.

2

Press the 

Intensity

 softkey; then, turn the Entry knob 

 to change the 

intensity of the displayed grid.

The intensity level is shown in the 

Intensity

 softkey and is adjustable from 0 to 

100%.

Each major vertical division in the grid corresponds to the vertical sensitivity 

shown in the status line at the top of the display.

Each major horizontal division in the grid corresponds to the time/div shown in the 

status line at the top of the display.

To freeze the display

To freeze the display without stopping running acquisitions, you must configure 

the 

[Quick Action]

 key. See 

"Configuring the [Quick Action] Key"

on page 291.

1

Once the 

[Quick Action]

 key has been configured, press it to freeze the display.

2

To un-freeze the display, press 

[Quick Action]

 again.

Manual cursors can be used on the frozen display.

Many activities, such as adjusting the trigger level, adjusting vertical or horizontal 

settings, or saving data will un-freeze the display.

Summary of Contents for DSO-X 2014A



























































































































































































































































































































































































Reviews:

No comments

Related manuals for DSO-X 2014A

NEC NEAX2400 ICS Installation Notes preview
NEAX2400 ICS
Brand: NEC Pages: 29
Hammer Strength MTSP Unpacking And Assembly Instructions preview
MTSP
Brand: Hammer Strength Pages: 18
Parkside PFMR 1600 A1 Operation And Safety Notes preview
PFMR 1600 A1
Brand: Parkside Pages: 95
ubbink Niagara LED 30 Operating Instructions Manual preview
Niagara LED 30
Brand: ubbink Pages: 30
Garden Treasures 60031 Quick Start Manual preview
60031
Brand: Garden Treasures Pages: 2
Össur PROPRIO FOOT W Instructions For Use Manual preview
PROPRIO FOOT W
Brand: Össur Pages: 82
Lumineux Eyebrook Installation Instructions preview
Eyebrook
Brand: Lumineux Pages: 2
Fast MT765 Challenger Installation-Parts preview
MT765 Challenger
Brand: Fast Pages: 31
Zafferano pencil Instructions For Use Manual preview
pencil
Brand: Zafferano Pages: 28
Basler 9 1661 00 100 Instruction Manual preview
9 1661 00 100
Brand: Basler Pages: 33
Dynamic DynaTrap DT1260-TUN Owner'S Manual preview
DynaTrap DT1260-TUN
Brand: Dynamic Pages: 4
Elma Elmasonic P Operating Instructions Manual preview
Elmasonic P
Brand: Elma Pages: 35
Qtx DMX-192 User Manual preview
DMX-192
Brand: Qtx Pages: 6
B. Braun Aesculap S4 Cervical Instructions For Use/Technical Description preview
Aesculap S4 Cervical
Brand: B. Braun Pages: 43
Enabling Technologies Dynamique Biski Owner'S Manual preview
Dynamique Biski
Brand: Enabling Technologies Pages: 44
Dräger Medical Narkomed GS Operator'S Instruction Manual preview
Narkomed GS
Brand: Dräger Medical Pages: 204
GreenIQ GIQ-SYS-EU-16C1 Installation Manual preview
GIQ-SYS-EU-16C1
Brand: GreenIQ Pages: 76
Focal Meditech Gowing2 Quick Start Manual preview
Gowing2
Brand: Focal Meditech Pages: 10

Brands by name

Popular brands

Load more brands