Keysight Technologies B1505A Configuration Manual Download Page 65

Page: 65 / 298

Keysight B1505A Configuration and Connection Guide

1-57

Configuration Guide

Other Accessories

Other Accessories

The following table lists the options and accessories available for the B1505A.

Table 1-27

Options and Accessories

Model/Option

Description Additional

Information

Keysight EasyEXPERT software

B1540A-001

Standard edition

Keysight Desktop EasyEXPERT software

B1541A-001

Standard edition

Accessories for B1500 series

16444A-001

USB keyboard

16444A-002

USB mouse

16444A-003

Stylus pen

Cables, adapters, interlock

16493K-001

Kelvin Triaxial Cable, 1.5 m length

•

Cable length 1.5 m or 3.0 m can
be specified by option 001 or
002.

•

These cables are NOT
supported by the N1265A,
N1266A, N1267A and
N1268A.

16493K-002

Kelvin Triaxial Cable. 3.0 m length

Summary of Contents for B1505A











































































































































































































































































































Search results

Summary of Contents for B1505A

Reviews:

Related manuals for B1505A

Brands by name

Popular brands

Keysight Technologies B1505A, Configuration Manual

Search results

Summary of Contents for B1505A

Reviews:

Related manuals for B1505A

Brands by name

Popular brands