manualshive.com logo in svg

Kerlink 1LOC868-1W868-EU, Installation And Maintenance Manual, Page: 126 / 221

Share
Download
Kerlink 1LOC868-1W868-EU Installation And Maintenance Manual Download Page 126

 

Wirnet iBTS

 

Document title : Installation and 
Maintenance Manual 
Version : 2.0 
Author : SNI 
Date : 04/12/2018 

 

Classification

 

This document is the strict property of Kerlink and shall not be either copied nor sent without express 

written authorization of Kerlink 

Internal Use 

Kerlink m2m technologies reserved rights 

Confidential 

Kerlink – 1 rue Jacqueline Auriol – 35235 THORIGNÉ-FOUILLARD

 

Page 126 / 221

 

Strict confidential 

 

1.  This  equipment  should  be  installed  and  operated  such  that  a  minimum 

separation  distance  of  20  cm  is  maintained  between  the  radiator  (antenna) 
and user’s/nearby person’s body at all times. 

2.  This transmitter must not be co-located or operating in conjunction with any 

other antenna or transmitter. 

2.2.2

 

Canada / IC 

The Wirnet iBTS 915 is compliant to: 

-

 

CAN/CSA-C22.2 NO. 60950-1-07 / A1: 2011 / A2: 2014 

The power supply of the Wirnet iBTS 915 must be a limited power source. 
 
The Wirnet iBTS 915 is also compliant to IC - RSS 247 regulations: 

-

 

RSS-Gen  –  Issue  4,  November  2014-  General  requirements  and  Information  for  the 
Certification of radio Apparatus 

-

 

RSS-247 Issue 1, May 2015 - Digital Transmission Systems (DTSS), Frequency Hopping 
Systems (FHSS) and License-Exempt Local Area Network (LE-LAN) Devices 

 
The associated IC identifiers of the Wirnet iBTS 915 are: 

IC : 20637-KLK915IBTS 
Model : WIRNET iBTS 915 
Contains / Contient IC : 2417C-MC7355 
Model : MC7355 

 
The associated IC identifiers of the Wirnet iBTS Compact 915 are: 

IC : 20637-KLK915IBTSC 
Model : WIRNET iBTS Compact 915 
Contains / Contient IC : 2417C-MC7355 
Model : MC7355 

 
This device complies with Industry Canada’s license-exempt RSSs. 
Operation is subject to the following two conditions: 

1. This device may not cause harmful interference, and 
2. This device must accept any interference received, including interference that may 

cause undesired operation of the device. 

 

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio 
exempts de licence. 
L'exploitation est autorisée aux deux conditions suivantes: 

1. L’appareil ne doit pas produire de brouillage;

 

2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si 

le brouillage est susceptible d'en compromettre le fonctionnement. 

 

Summary of Contents for 1LOC868-1W868-EU






























































































































































































































Reviews:

No comments