Home
/
Kerlink
/
1LOC868-1W868-EU
/
Installation And Maintenance Manual

Kerlink 1LOC868-1W868-EU, Installation And Maintenance Manual, Page: 119 / 221

Share

Page: 119 / 221

Kerlink 1LOC868-1W868-EU Installation And Maintenance Manual Download Page 119

Wirnet iBTS

Document title : Installation and
Maintenance Manual
Version : 2.0
Author : SNI
Date : 04/12/2018

Classification

This document is the strict property of Kerlink and shall not be either copied nor sent without express

written authorization of Kerlink

Internal Use

Kerlink m2m technologies reserved rights

Confidential

Kerlink – 1 rue Jacqueline Auriol – 35235 THORIGNÉ-FOUILLARD

Page 119 / 221

Strict confidential

Figure 81 : Dome antenna bracket with notched V shaped bolt

1.8.7

Debug tool

The Wirnet iBTS has a proprietary serial debug interface named DEBUG available on the
front panel of the CPU module.
This debug interface is intended to be used by authorized and qualified personnel only.
The WIRMA2 Debug tool is intended to be connected to the debug interface. It is mainly a
simple UART to USB converter.

The main characteristics of the Wirma2 debug tool are:

Characteristics

Specification

UART Interface

RJ45 female
3.3V internal LDO
Up to 1Mb/s

USB2.0 interface

USB 2.0 A type
USB Self Bus Powered at 5V
Full Speed (12Mb/s)

Operating temperature range

0°C to +60°C

Chipset

FT232BL (FTDI)

The debug tool must be used with an Ethernet cable and a USB2.0 type A to type B male
cable. They can be provided by KERLINK as options as detailed in §6.
The USB cable must be connected to a computer where must be installed HyperTerminal or
Teraterm to visualize the traces.

«
...
117
118
119
120
121
...
»

Summary of Contents for 1LOC868-1W868-EU






























































































































































































































Reviews:

No comments